AMD Processors
Decrease font size
Increase font size
Topic Title: HOT! MP
Topic Summary:
Created On: 10/07/2005 01:02 PM
Status: Read Only
Linear : Threading : Single : Branch
Search Topic Search Topic
Topic Tools Topic Tools
View similar topics View similar topics
View topic in raw text format. Print this topic.
 10/07/2005 01:02 PM
User is offline View Users Profile Print this message

Author Icon
Junior Member

Posts: 1
Joined: 10/07/2005

need help! i have AMD 2400 MP's and the tempatures are abnormally high... ive been many different places, and i need some help. the idle temps are 62c and 59c full load they are around 70c i just put new sinks on and some artic silver 5, and i just ordered some copper shims to help with conductivity.(a side note... can you put thermal paste directly on the processor... if not do the shims really help that much?) so what exactly should i do... i should have more than adequate case cooling... help would be appriciated
 10/07/2005 04:09 PM
User is offline View Users Profile Print this message

Author Icon
MD - Moderator
Deployer of Mjölnir - House Keeping

Posts: 11102
Joined: 11/05/2003

Do not use shims...

MD's Temperature related standard checklist.

Check the following for overheating or perceived overheating:

- Is the heatsink correctly installed ?
--> Verify it is correctly installed.

- Is the heatsink filled with dust and crud ?
--> Clean with compressed air in a can.

- Is the heatsink fan operating ?
--> Replace defective fan with similar or better unit.

- Is the heatsink adequate for that application/CPU ?
--> Verify it meet the requirements for the CPU being used.
--> RETAIL heatsink? May require lapping and better TIM.

- Is thermal interface material used between heatsink and cpu ?
--> Verify it is used, and is applied according to the manufacturers guidelines.
--> Recommended PCM's, thermal pads from "AMD Thermal, Mechanical,and Chassis Cooling Design Guide #23794.PDF.
- Bergquist HF225UT Phase Change
- Chomerics T725 Phase Change
- Honeywell PCM45 Phase Change
- Power Devices Powerfilm Phase Change
- ShinEtsu PCS-TC-11T-13 Phase Change
- Thermagon T-pcm905C Phase Change
--> Recommended thermal interface material aka: grease, gel etc.
- Arctic Ceramique.
- Arctic Alumina.
- Arctic Silver, 3, 5 etc.

- Is the TIM pad cover removed from heatsink before installation, if using supplied TIM pad ?
--> Remove the cover before installation, failure to do so will insulate the cpu from the heatsink.

- Is there adequate airflow or case ventialation ?
--> Verify airflow, add case fans if required.

- Is the Vcore set higher than specified by the manufacturer ?
--> Verify the Vcore is set to the manufacturers specification in the mainboards bios.

- Is the temperature read via the internal temperature diode. Is the tremperature read via the socket thermistor ?
--> Temperatures read at the diode can and will be higher than an external reading.

- Is the temperature sensor properly calibrated ?
--> Several boards have this problem, check manufacturers bios revision history for calibration fix.
--> Does the heatsink feel warm or HOT, if it's warm it could be a miscalibration error.

- Outside temperature high ?
--> If the external temperature is high, then the case fans will be drawing in hot air, especially during summer months. Remeber, when it's Winter in the Northern Hemi-sphere, it's Summer in the Southern Hemi-sphere & vice-versa.


The opinions expressed above do not represent those of Advanced Micro Devices or any of their affiliates.

Physics? Ha! This is clearly magic and devilry at work. Prepare firewood! We have witches to burn!

112018 users are registered to the AMD Processors forum.
There are currently 0 users logged in.

FuseTalk Hosting Executive Plan v3.2 - © 1999-2015 FuseTalk Inc. All rights reserved.

Contact AMD Terms and Conditions ©2007 Advanced Micro Devices, Inc. Privacy Trademark information